Manual Systems

Off-cut Remover Hektor 2: Hektor separates milled PCBs carefully and fast. The offcut material is removed smoothly and precisely. The matrix consists of two parts. This ensures easy and cost-saving change of the blades. Compressed air is used for the separation process. The operating pressure can be set on the machine. When the foot switch is pressed, the off-cut is punched out. The off-cuts are collected in the collecting box. When the gate is opened the waste material can be extracted.

Separates milled PCBs carefully and fast.

The PCB is slipped with its milled groove over the blade and is placed onto the matrix. The off-cut is pulled under the blade. When the foot switch is pressed, the off-cut is punched out and the waste material is collected inside the machine.

Supplied with Footswitch and one L blade, size of your choice.

MAESTRO 2 separates small amount and prototype series of PCBs fast and economically. The compact and stable aluminum frame requires only a minimum of space. The PCB is held with both hands and fed between the circular blades for separation. The clearance between the upper guide and the lower guide is adjustable to ensure that the PCB is only fed through the machine in the pre-scored groove.

Separates large numbers of PCBs without fatigue of the operator. The lower circular blade is driven by a motor. The PCB is fed between the circular blades where it is seized, transported and separated. Three different speeds can be selected. Compact, fast and economical PCB separator for PCBs with pre-scored groove.

MAESTRO 3E separates both small and large pre-scord PCBs. The table and the rest can be continuously adjusted to the most suitable working position. The slit between the linear blade and the rest can be adjusted to ensure that the side strips fall through and are sorted out.

PCB Separator MAESTRO 3E For small and large PCBs and for PCBs with pre-scored groove

Strain of components: Frequently for critical components an upper limit of tensile stress will be determined. Please ask us regarding possibilities to reduce tensile stress of components.

Safe Operation:

The PCB is placed with its pre-scored groove onto the linear blade and the circular blade is then drawn by hand across the PCB. The clearance between the upper guide and the linear blade ist adustable to ensure that the PCB is only separated in the pre-scored groove.

MAESTRO 4S separates both small and large PCBs fast and economically. To optimize operation, the separation length can be programmed with the control keys.

Strain of components: Frequently for critical components an upper limit of tensile stress will be determined. Please ask us regarding possibilities to reduce tensile stress of components.

Safe Operation:

The PCB is placed with its pre-scored groove onto the linear blade. When the foot switch is pressed, the blade carrier with the circular blade moves across the PCB, separating it into individual units. The clearance between the upper guide and the linear blade is adjustable to ensure that the PCB is only separated in the pre-scored groove. The table can be continuously adjusted with the rotary knob whenever required while the rest can be adjusted in three steps to the most suitable working position.

DPF300 Depaneling System:

DPF300 the new model, is now using an electric micro spindle, instead of pneumatic, so no longer requires an air supply.

Premier HS203 separates both small and large PCBs fast and economically.

• To optimize operation, the separation length can be programmed with the control keys. Minimises strain on components Safe Operation:
• The PCB is placed with its pre-scored groove onto the linear blade. When the foot switch is pressed, the blade carrier with the circular blade moves across the PCB, separating it into individual units.
• The clearance between the upper guide and the linear blade is adjustable to ensure that the PCB is only separated in the pre-scored groove.
• The table can be continuously adjusted with the rotary knob whenever required while the rest can be adjusted in three steps to the most suitable working position.

Premier HS206 separates both small and large PCBs fast and economically.

• To optimize operation, the separation length can be programmed with the control keys. Minimises strain on components Safe Operation:
• The PCB is placed with its pre-scored groove onto the linear blade. When the foot switch is pressed, the blade carrier with the circular blade moves across the PCB, separating it into individual units.
• The clearance between the upper guide and the linear blade is adjustable to ensure that the PCB is only separated in the pre-scored groove.
• The table can be continuously adjusted with the rotary knob whenever required while the rest can be adjusted in three steps to the most suitable working position.